[chip_conf] #芯片类型可以是 ESP32 ESP8285 ESP8089 和 ESP8266 CHIP_TYPE = ESP8266 #存放测试结果的路径 LOG_PATH = ./ logs FACTORY_INFO = XXXXXXX BAUDRATE = 115200 IMGPATH = ./image/ESP8266_MOD118_26M_20171013.bin FREQ = 26 AUTOSTART = 1 SKIP_DOWNLOAD = 0 #1:天线测试 0:cable测试 ANTENNA = 1 INITFROMXLS = 0 EFUSE_MODE = 1 UART_TEST_REBOOT_DELAY_MS = 0 ANALOG_TEST_RETRY_LIMIT = 1 [fixed_conf] ESP_SERVER_UPLOAD_EN = 0 ESP_SERVER_ADDR = 120.76.204.21 ESP_SERVER_PORT = 6666 ESP_SERVER_TIMEOUT = 3 DEVICE_TYPE = ESP_WROOM02 BATCH_SID = bf54c4adf0 FACTORY_SID = esp-own-test-FID-dbd42d01 FW_VER = 0.0.0.0 CHK_REPEAT_FLG = 0 PO_TYPE = 0 CUS_MAC_ADDR = 0xfc000 SAVE_MAC_IN_CSV = 1 SAVE_MAC_PATH = /config/mac.csv ESP_PRINT_TAG_EN = 0 ESP_PRINT_CMD = ./cmd_test/ESPPrintLabel20160705/ESPPrintLabel.exe ESP_STUB_EN = 0 IP_FACTORY_NAME = CH [test_item_en] ANALOGTEST = 1 TXTEST = 1 RXTEST = 1 PSRAMTEST = 0 PVTTEST = 0 GPIO_8266_TEST_EN = 0 GPIO_32_TEST_EN = 0 FLASH_ID_CHECK_EN = 0 FLASH_RW_CHECK_EN = 0 ADC_TEST_EN= 0 ESP32_ADC_EN = 0 ESP32_ADC_REF_CAL_EN = 0 ESP32_ADC_REF_MEAS_EN= 0 ESP32_WRITE_EFUSE_EN = 0 ESP32_FLASH_80M_CHECK_EN = 0 Volt_Means_EN = 0 #是否在flash中写mac地址 SET_MAC_EN = 0 #是否运行外部exe TEST_RESULT_HANDLER_EN = 0 CUSTOMER_DEFINITION=0 [test_item_param] FLASH_ID = 0x4016 FLASH_RW_ADDR = 0x1FA000 FLASH_DEVICE_ID_ADDR = 0x1FA000 PVT_THRES = 3300 TESTER_COMPARE_THREHOLD= 20 TESTR_GPIB_ADDRESS =GPIB0::23::INSTR TESTER_COMPARE_TARGET = 2350 #写flash中mac地址配置项 MAC_INPUT_EN = 0 MAC_OFFSET = 0x81000 MAC_START = AA0000000000 MAC_END = AA0000000100 MAC_CURRENT = aa0000000051 #写flag位置 FLASH_FLAG_EN = 0 FLASH_FLAG_OFFSET=0x1100 FLASH_FLAG_READ_EN=0 #ESP8266 GPIO测试配置项 GPIO_8266_TEST_PIN = 0x3030 GPIO_8266_TEST_VAL = 0x1010 GPIO_8266_TEST_READ_EN = 0 GPIO_8266_TEST_VAL_TARGET = 0x3030 #ESP32 GPIO测试配置项 GPIO_32_TEST_VAL_0 = 0xD9000C20 GPIO_32_TEST_VAL_1 = 0x0054E0E0 GPIO_32_TEST_VAL_2 = 0x00000055 GPIO_32_TEST_TARGET_0 = 0x33000000 GPIO_32_TEST_TARGET_1 = 0x00AC0000 GPIO_32_TEST_TARGET_2 = 0x000000BB ESP32_PAD_INIT = adccal_pad_init 6 7 4 5 6 7 3 1000 ESP32_PSRAM_CMD = psram_op 0x0 0x5aff00a5 16 5 3 3 #ESP32 FLASH_CMD DEF ESP32_FLASH_80M_TEST_CMD = flash_op 0x0 0x5aff00a5 16 0 1 6 5 3 3 1 ESP32_FLASH_PASS_FREQ_MHZ = 88 TEST_RESULT_HANDLER_FUNC_PATH = .\image\EPC_client_v1.3.3.py Module_SYNC_COUNTS = 2000 SER PRINT RETEST = 1 [fw_test] # 是否测试固件的总开关 USER_FW_EN = 1 #测试方式一:发送指令数目 USER_TEST_CMD_NUM = 0 USER_TEST_CMD0 = AT+GMR USER_TEST_RESP0 = 1.0.b1.0 USER_TEST_TIMEOUT0 = 5 USER_TEST_CMD1 = AT+CWLAP USER_TEST_RESP1 = OK USER_TEST_TIMEOUT1 = 5 USER_TEST_CMD2 = AT+GMR USER_TEST_RESP2 = OK USER_TEST_TIMEOUT2 = 5 #测试方式二:看打印或IO状态 0: disable ; 1: uart 2: gpio USER_FW_VER_TEST_EN = 1 USER_FW_VER_BAUD = 115200 USER_FW_VER_STR = 123 USER_FW_VER_TIMEOUT = 3 #是否下载固件 USER_FW_DOWNLOAD_EN = 0 #下载固件的接口: SPI OR HSPI USER_FW_DOWNLOAD_PORT = SPI #0:RF等测试通过后下载 ; 1:测试完成后下载 USER_FW_FORCE_DOWNLOAD = 0 USER_FW_FILE_NUM = 0 USER_FW_PATH0 = ./image/blank.bin USER_FW_ADDR0 = 0xfc000 USER_FW_PATH1 = ./bin/test.bin USER_FW_ADDR1 = 0x0